Automated Endoscope Reprocessors

An automated endoscope reprocessor (AER) is the preferred method over manual soaking for reprocessing complex endoscopes. After cleaning, the automated process in an AER circulates either the high-level disinfectant or liquid chemical sterilization solution around the exterior and through the device channels for a timed exposure period, followed by rinsing. STERIS AERs are available in one-sided or pass-thru configurations. Both support best practices by allowing for unidirectional workflow.

REQUEST A QUOTE

Liquid Chemical Sterilization

Liquid chemical sterilization (LCS) provides a higher level of reprocessing assurance for heat-sensitive critical and semi-critical medical devices compared to high-level disinfection. LCS eliminates all viable microbial life, including bacterial spores such as C-Diff, supporting infection prevention best practices. STERIS's automated liquid chemical sterilant processing systems are preferred for low temperature LCS of heat-sensitive complex endoscopes, including flexible multi-channel devices and other high-risk endoscopes such as bronchoscopes, duodenoscopes, cystoscopes, and endobronchial ultrasounds.

enspire™ 3000 Series Cleaning and Liquid Chemical Sterilant Processing System

Validated Cycle: Automated cleaning and liquid chemical sterilization in 38 minutes
Devices: Reusable, heat-sensitive, semi-critical medical devices and their accessories
Features: The first and only AER with liquid chemical sterilization and a validated cleaning claim*

System 1™ endo Liquid Chemical Sterilant Processing System

Validated Cycle: Liquid Chemical Sterilization in a rapid 18-minute cycle time
Devices: Cleaned, reusable, heat-sensitive, semi-critical medical devices and their accessories
Features: Liquid chemical sterilization which eliminates all viable microbial life, including bacterial spores such as C-Diff

System 1E™ Liquid Chemical Sterilant Processing System

Validated Cycle: Liquid Chemical Sterilization in a rapid 23-minute cycle time
Devices: Cleaned, reusable heat-sensitive critical and semi-critical medical devices
Features: Liquid chemical sterilization which eliminates all viable microbial life, including bacterial spores such as C-Diff

*Cleaning claim does not apply to duodenoscopes

High-Level Disinfection

High-level disinfection (HLD) kills or inactivates microorganisms that could cause infection when used according to product labeling. Automated processing provides efficient, consistent, and measurable outcomes to eliminate all microorganisms in or on an instrument, except for small numbers of bacterial spores. STERIS helps you maintain a safe and compliant HLD process for your staff and patients with validated products for complex endoscopes.

MEDIVATORS™ ADVANTAGE PLUS™ Pass-Thru Automated Endoscope Reprocessor

Cycles: Validated high-level disinfection (HLD) after manual cleaning
Workflow: Pass-thru endoscope reprocessing with no-touch workflow to reduce cross-contamination
Capacity: Asynchronous bays allow you to HLD endoscopes individually in a 35-39 minute cycle

MEDIVATORS™ ADVANTAGE PLUS™ Automated Endoscope Reprocessor

Cycles: Validated cleaning claim and high-level disinfection (HLD) process
Workflow: No-touch workflow to reduce cross-contamination in this single-sided system
Capacity: Asynchronous bays allow you to clean and HLD endoscopes individually in a 35-minute cycle*

enspire™ 300 Series Automated Endoscope Reprocessor

Cycles: Validated cleaning claim and high-level disinfection (HLD) process
Workflow: Allows for flexibility with either pass-thru or single-sided configuration
Capacity: Clean and HLD up to two endoscopes or six non-channeled naso-endoscopes at the same time in a 34-minute cycle*

MEDIVATORS™ DSD EDGE™ Automated Endoscope Reprocessor

Dual basins provide high level disinfection in either simultaneous or independent cycles
Reprocessing cycle time as short as 22 minutes allows for quick endoscope turnaround
Large basins accommodate most endoscope sizes